Oil and moisture are common culprits. Moisture causes problems when it is in the air, in the nail polish, and on your hands. Cuticle oil, lotion, and food on your hands may be to blame. Shaking the bottle of nail polish before the application will let air bubbles into the nail polish. Shaking, waving, blowing on your hands, or holding them in front of a fan to dry faster are also bad ideas. Bubbles can also appear when you skip a clear base coat and topcoat for your manicure. Cleaning your hands and nails will get rid of moisture and oil that will spoil your mani.
Wash your hands with warm and soapy water, and clean beneath each nail too. Knowing how to tell if nail polish is bad is quite simple. Check the quality of your nail polish by applying a quick swipe across one of your nails as a test. Old and gloopy nail polish will not give you the smooth and perfect-looking manicure you deserve.
Stay away from thick and creamy nail polish at all costs if you want to avoid bubbles in the first place. This prevents these oils from spoiling your manicure. Base coats provide an even and smooth finish. Thick layers of nail polish take forever to dry and are a lot more likely to form air bubbles. You must let your nail polish dry completely before you paint another layer.
Dipping your hands in ice-cold water for a minute is a great way to help your polish dry quickly. Never created a password? Create one here. Already have an account?
Log in here. Thanks, but no thanks. No, thanks I'm already a PureWow fan. No, thanks I hate pretty things. Everything about this is relaxing Why does this happen? Bubbles typically surface during the drying process because of air getting trapped between layers of polish. Step 1: Always start with a clean slate—even if your nails are bare.
Using polish remover, wipe your nails completely free of any oil or residue that could prevent polish from adhering properly. Step 2: Paint in thin layers. This is key because thick coats of polish take longer to dry. Much like putting on primer before your foundation, a base coat is necessary for a smooth and even finish.
Applying a base coat not only prevents nail discoloration, but it also extends the wear of your manicure. Since your nails emit natural oils that prevent the nail polish from adhering well, a base coat is the best way to seal these oils in.
It is just not realistic. Test your nail polish beforehand with a quick swipe across your nail to check if it is the right consistency. If your polish is thick, dense, and sticky, either thin it out with lacquer thinner or throw it away. Shaking a bottle of nail polish vigorously is probably the number one mistake we have all made. Doing so only traps the air inside the bottle, which creates tiny pockets where bubbles form.
Those air bubbles, when transferred onto your nails, sometimes leave noticeable holes in your manicure. If your polish has separated, the best way to deal with it is to simply roll the bottle between your hands like you are rolling dough.
The key to a perfect manicure lies in its application. If you have too much polish on your brush, you are in for a mess. If a gel polish thinner is available, put a few drops of this solution to the gel bottle and vigorously shake for 1 or 2 minutes.
Inspect the gel consistency on the brush. It should be thick but readily dripping off the brush. Use more gel polish thinner if necessary. It is a good practice to know how to fix thick gel polish with thinner. If the gel inside the bottle is so thick that it deforms the brush bristles, discard it. It already solidifies and can not be brought back to liquid form.
Next, all UV lamps whether it is a lamp using fluorescent bulbs or LED light emittd diodes will diminish or get weaker over time with the bulb type lamps do so quicker. When this happens the amount of UV light generated will be reduced compared to the new one and so its energy to cure gel polish will also be reduced, This will cause the gel polish to be under cured, meaning the surface will cure first and prevent light from going deeper to cure lower gel layer.
Inadequate or insufficient power UV light sources will cause the same effect and might not cure gel polish completely. To determine if a UV lamp is in good condition or not, polish 3 nail tips with black, white, and one dark gel color then curing them with recommended time under the UV lamp in question. Repeat polish the three nail tips one more time.
If after the second time, any of the three polish colors wrinkles or bubbles or still feeling sticky when touched, the UV lamp does not produce enough light. To correct this situation, the old bulbs in a UV lamp must be replaced with new ones and the above test should be repeated to ensure improvement. If this happens to an LED type UV lamp, this lamp is defective or at the end of its working life and should be properly discarded.
Many of the smaller home use type of UV lamps generate about 6 watts of UV light energy as compared to those larger sized, professional ones which generate more than 30 watts in UV light energy.
Any reduction in UV light of these smaller, home use types will dramatically affects their gel polish curing ability than that of full-sized, professional ones. Also, some smaller, home use UV lamps do not come with a bottom reflective plate.
With this plate being used, the UV light shines down will reflect back to the top side and will partially reflect back on the nails so the light intensity will be enhanced. If your UV lamp does not have a bottom plate, put it on a reflective metal tray, or a smooth, light color table surface before curing gel polish. Remember this feature the next time you are in the market for a UV lamp.
Lastly, even though you do all four things mentioned above and gel polish still have wrinkled or bubbled, it may be that the nails are not placed where it should be for optimal light intensity and energy. White, black or dark color gel polish requires adequate light intensity they need in order to cure completely. If nails are not placed at the right location, UV light that shines on the nail surface will be at an angle and some will be reflected away instead of being absorbed in the polish, causing gel polish to be cured on top and under-cured inside.
Make sure that all nails are facing the light. Thumbs and pinky ones are the ones that usually have this problem. Instead of spending money on your nails, you can make a full time income and stay home by just writing about it in your free time. Most lights will reflect away from the white color so if white gel polish is too thick, as the top layer cures, this cured layer will prevent light from coming through and there will not be enough light energy to go cure lower layer.
0コメント